8208 Hot Air gun Heat Gun Hot Air Station-Foshan jcsolder Co., Ltd

8208 热风枪

产品描述：

Model: 8208Dimensions: L 266mm x W 50mm × H 35mmProduct weight: 573gVoltage: AC220-240V / AC100-130VFrequency: 50Hz / 60HzOutput power: 750WTemperature range: 100°C to 520°CTemperature stability: ±...

产品型号：

更新时间：

2024-01-12

访问量：

服务热线：13637323895

立即咨询

产品介绍
参数规格
Documents
视频
相关产品
FAQS

Model: 8208

Dimensions: L 266mm x W 50mm × H 35mm

Product weight: 573g

Voltage: AC220-240V / AC100-130V

Frequency: 50Hz / 60Hz

Output power: 750W

Temperature range: 100°C to 520°C

Temperature stability: ±2°C

Air flow: 120L/min(MAX.)

Operating temperature: 0~40°C/32~104°F

Product Questions and Answers

Q - What is the Millermatic 211's maximum welding thickness? A - The Millermatic 211 can weld up to 3/8" steel or aluminum in a single pass when plugged into a 240V power supply. With a 120V power supply, Millermatic 211 can weld up to 3/16" steel or 1/8" aluminum.

Q - If I cut the plug off of the Millermatic 211 and change it will the machine still work? A - The Millermatic 211 comes with MVP style plugs for running the machine off of 110v or 230v. If done correctly, the plug can be cut off and a regular one can be put on.

Q - Can the Millermatic 211 be used to TIG weld? A - The Millermatic 211 is for MIG welding only.

Q - What size generator should I use for the Millermatic 211? A - The Millermatic 211requires a generator that can produce 7500 Watts continuous.

Q - What size aluminum can the Millermatic 211 weld? A - On a single pass, the Millermatic 211 can handle 1/8" aluminum at 120V and 3/8" at 230V.

Q - What's the largest spool that can be used with the Millermatic 211? A - The Millermatic 211 works with 8-inch spools and 4-inch spools. You can use .024–.035 inch (0.6–0.9 mm) solid wire and .030–.045 inch (0.8–1.2 mm) flux-cored wire.

Q - What kind of power source does the Millermatic 211 need? A - The Millermatic 211 comes with a 120/240 V, 50/60 Hz power source. It works with standard 120V single-phase household power supplies as well as 240V outlets for greater power.

Q - Where is the Millermatic 211 made? A - The Millermatic 211 is designed, engineered and assembled using proprietary technologies in Appleton, Wisconsin.

How to Set Up Millermatic 211 for the First Time:

Review the safety tips in the Owner's Manual.

Review the instructions for important safety information before using your Millermatic 211 welding machine. Ensure you are wearing OSHA-approved personal protective equipment during setup, maintenance and welding. A helmet with at least a shade 10 lens is recommended.
Connect the control cable.
Pull the work lead out of the access hole on the front of the machine. Locate the control cable connection on the inside of the door, under the drive. Route the control cable through the access hole and connect the cable to the four-pin connection, twisting the collar to secure it in place.
Connect the MIG gun.
Insert the MIG gun into the drive casting, making sure it is completely seated into the drive assembly. Tighten the threaded T-knob. For aluminum welding, instructions are provided for installing the optional Spoolmate 100 spool gun.
Connect the work clamp.
Route the work lead through the work clamp, connect, and tighten securely. Ensure the work cable is connected to the negative output terminal for solid wire with shielding gas.
Set up shielding gas.
Choose the appropriate gas (75/25 mix, 100% CO2, tri-mix for stainless steel, 100% argon for aluminum). Connect the gas hose to the regulator and machine, purge the gas cylinder, and secure connections.
Install drive roll and wire.
Select the correct drive roll groove based on wire size. Place the wire spool on the shaft, thread the wire through the inlet guide and MIG gun liner, and adjust tension settings.
Complete initial setup.
Plug in and power on the machine, avoiding extension cords if possible. Feed the wire through the gun, select the appropriate contact tip, and adjust the drive roll tension.
Choose Auto-Set or manual mode.
Use the parameter chart inside the door for initial settings. Utilize the Auto-Set feature on Millermatic 141 and 190 for mild steel and 75/25 gas, and the Advanced Auto-Set on Millermatic 211 for various materials and gases.
(Optional) Install spool gun for aluminum welding.
Use 100% argon gas and follow similar installation steps as the MIG gun. The spool gun holds the wire spool and automatically detects when the trigger is pulled, with no need for a spool gun switch.

8208 热风枪

Accessories

Consumables

Accessories

Consumables

Product Questions and Answers

How to Set Up Millermatic 211 for the First Time:

留言框

Company Name：

Country：

Whatsapp/Phone：

E-mail：

留言内容：

验证码：